What are the common faults and troubleshooting methods for high-speed automatic T-shirt bag making machines?

Mar 04, 2026 Leave a message

High-speed automatic T-shirt bagging machine is the key equipment of modern packaging industry. Its efficient and stable operation is essential to improve production efficiency and product quality. However, due to its complex structure and fast running speed, it is inevitable that various faults will occur in practice. This paper will introduce the common faults and their troubleshooting methods of high speed automatic T-shirt bagging machine in detail to assist operators better maintain and repair the equipment.
I. Fault and Troubleshooting in the electrical system
1.The machine does not start or operate properly
Fault Causes:
The main motor lacks power or unstable voltage.
The Hall switch or proximity switch signals of the main motor is lost.
The inverter or servo drive of the main motor has the self-protection function of fault.
Wire broken or badly touched.
Troubleshooting Methods:
Use multimeter to check the three-phase input voltage and neutral line are normal to ensure the power supply is stable.
Check the connection between the main motor Hall switch and proximity switch to ensure safety and signal normality.
Observe the indicator lights on the inverter or servo drive. In case of alarm, troubleshoot and repair as per instruction manual.
Check the equipment's wiring, especially areas prone to wear and tear and aging, and repair or replace broken wiring in a timely manner.
2. The Control Panel Has not showing or buttons not working
Fault Causes:
Switch power supply does not output 24V voltage.
A damaged proximity switch can cause the circuit to open, causing power indicator light not to glow.
There is something wrong with the computer board.
Troubleshooting Methods:
Check the output voltage of the switching power supply using the multimeter. If there is no output, replace the switching power.
Check the connection and status of the proximity switch. If damaged, please replace it.
If the computer board is malfunctioning, try rebooting the device or replacing the computer board.
ii. Malfunction and Troubleshooting of mechanical systems
1. Slash, slash, slash
Fault Causes:
The blade wears or dulls.
The balance between the upper and lower blades is poor, and the blade sliders wear too much, resulting in too much clearance.
Heat blade temperature is set improperly or heated unevenly.
Thin film electrostatic too much, affect the cutting effect.
Troubleshooting Methods:
Periodically check the wear and tear of the blade and polish or replace the blade in time.
Adjust the balance between the upper and lower blades to ensure that the blade sliders have proper clearance.
Adjust the heat blade temperature according to the film material to ensure uniform heating.
Check electricity treatment of the film. If the static electricity is too strong, please replace the film.
2. The seal is not strong, or one side is strong and the other is not
Fault Causes:
Insufficient sealing temperature or low pressure.
Too small pressing of hot rods or ageing and hardening of silicone pad.
Film lamination is uneven or thickness is not uniform.
The photoelectric tracking is inaccurate, resulting in the displacement of seal position.
Troubleshooting Methods:
Adjust the sealing temperature and pressure according to the film material to ensure a strong seal.
Replace aging silicone pad and adjust the pressure of hot rods.
Check the lamination and thickness uniformity of the film to ensure uniformity.
Adjust the sensitivity and position of photovoltaic tracking to ensure an accurate seal position.
3. The Bag Sizes Are Inconsistent or Deformed or deformed with Upturned Corners
Fault Causes:
Pocket length is inaccurate due to printing or lamination.
The traction rubber roller slips or has uneven pressure.
Hot rods are pressurized or overheated.
Film thickness is not uniform or laminar pressure is not uniform.
Troubleshooting Methods:
Check the printing and lamination processes to ensure the length of the bag is accurate.
Adjust the pressure and balance of the traction cots to prevent skid.
Adjust the temperature and pressure of the hot rod to avoid material being pressurised and overheated.
Check the thickness and laminating uniformity of the film.
III. Fault and troubleshooting of Pneumatic System Faults
1. The Pneumatic Cylinder do not drive or drive slowly
Fault Causes:
Insufficient air source pressure or air circulation leaks.
The solenoid valve is faulty or the wire is broken.
the pneumatic cylinder inner parts wear or seals age.
Troubleshooting Methods:
Check gas source pressure to ensure compliance with equipment requirements.
Check the connection and sealing of the air loop and find out the air leaks in time for maintenance.
Check connection and status of the solenoid valve. If there is a problem, please replace it.
Remove the pneumatic cylinder check for internal wear and seal conditions. Replace worn parts and seals in a timely manner.
2. The Vacuum Suction Cup cups lack suction or fail
Fault Causes:
Vacuum generator jammed or malfunctioning.
suction cup wear or age.
Air hoses are not tightly connected or leak.
Troubleshooting Methods:
Clean the impurities and dirt inside the vacuum generator to ensure that the vacuum generator is not blocked.
Check for wear and tear and aging of suction cup and replace them in time.
Check air hoses connections and seals to make sure they are tight and no air leaks.
IV. INTRODUCTION Other Common Faults and troubleshooting
1. Photoelectric Tracking lost or unstable
Fault Causes:
The distance between the photoelectric head and the film is not suitable.
The photoelectric head are not vertical or sensitively set properly.
After sealing, the The film deforms, stretch or wrinkle.
The photoelectric frame is not tightly locked and the tracking range is not reasonable.
Troubleshooting Methods:
Adjust the distance between the photovoltaic head and the film to an appropriate range.
Ensure the photovoltaic head is vertical and adjust the sensitivity to appropriate values.
Check the sealing process of the film to avoid deformation and wrinkling.
Lock the photoelectric frame and set the tracking range reasonably.
2.Machine noise or vibration
Fault Causes:
Instability of machine installation or loosening of anchor bolts.
Machine accessories worn or loose.
Bearing, gear and other Transmission components damaged.
Troubleshooting Methods:
Reinstall the machine to ensure stability and tighten the anchor bolts.
Check the wear and tear of machine accessories and replace or tighten them in time.
Check the status of bearing, gear and other transmission components, if there is damage should be promptly replaced.
3.The Equipment Overheats or Has Abnormal Temperature
Fault Causes:
The cooling system malfunctioned or has poor cooling performance.
The equipment operated under high load for a long time.
temperature control are faulty or improperly set.
Troubleshooting Methods:
Check that cooling system components such as fan and heat sinks are working properly and remove dust and dirt.
Arrange the running time and load of equipment rationally to avoid long term high load operation.
Check the setting and status of the temperature control system. If something goes wrong, fix or adjust the settings.